Top 9 Low Foltage Induction Heating

0
590 reviews analysed

1. Treedix 5-12V ZVS Low Voltage Induction Heating Power Supply Module with Coil Power Supply Heating Power Supply Module

Treedix 5-12V ZVS Low Voltage Induction Heating Power Supply Module with Coil Power Supply Heating Power Supply Module

Feature

Description

Specification:
Input Voltage:DC 5V~12V
Max Power:120W
PCB Size:55 x 37 x 1.6 mm

Package Included:
1 x ZVS heating Power Source module
1 x heating coil

Note:
1. When inductive heating, usually work for 5 minutes to power off cooling. Because the current is relatively large during induction heating, the coil heat is also relatively large. When heating, part of the heat generated by the heated object is transmitted to the heating coil. For a long time, the temperature of the heating coil is high. If the heating coil is connected to the terminal, the plastic part of the terminal will be melted. Therefore, when induction heating, it is best to solder the heating coil directly to the PCB
2. Only some types of materials can be effectively induction heated – mostly magnetic materials such as steel. Materials such as brass, copper and aluminum will be very difficult to heat.
3. A large capacitor placed in parallel with the supply voltage can help reduce the voltage/current drop that prevents the unit from starting.
4. This module should not be operating when no load, otherwise it might burn out the circuit.
5. You can check whether the blue LED indicator light up to see if the power is supplied or the module can functionally work. When the indicator is dim, maybe the power supply is insufficient, should use a higher power supply. Just make sure the power supply is within DC 5-12V.
Remark: You can solder the heating coil on the board.

2. KOOBOOK 1Pcs 1000W ZVS Low Voltage Induction Heating Board Module Flyback Driver Heater 12V-48V DIY

KOOBOOK 1Pcs 1000W ZVS Low Voltage Induction Heating Board Module Flyback Driver Heater 12V-48V DIY

Feature

Description

Specifications:
Inside diameter of the coil: approx. 40mm
Height of the coil: approx. 50mm
24V input with no load current of 3A
48V input with no load current of 6A
It suits 12-36V power supply (not included)
The coil accept 40mm crucible

Note:
The use of switching power supply Please note that due to high power are generally slow start function, which just opened machine output voltage is slowly rising, while it is turned on before the induction heating circuit if the voltage rises to 12V, because start insufficient voltage can not afford to vibration, resulting in two simultaneous conduction mos tube so burned components.
So the first will start switching power supply voltage reaches 12V above and then access the induction heating circuit.
The volume of the object being heated inside the heating coil can not exceed 1/5 of the volume (if the heating cylinder, then heating coil diameter less than the diameter of 1/3), or it may be due to overload or burn out the power supply to the circuit.
Although this circuit can tolerate 20-30A input current moment, but do not exceed 15A when safe work, you can easily add an ammeter between the power supply and heating driver board but always monitor the current overload.
This circuit can not only do the induction heating, the copper tube into the high-frequency transformer, is a powerful inverter.

We highly appreciate all customers opinions to improve the selling, also if anything you unsatisfied, please contact us for probable best solution.

Package Includes: 1Pcs
1 x ZVS low voltage induction heating board
1 x brass coil

3. 1000W ZVS Low Voltage Induction Heating Board Module Flyback Driver Heater DIY

1000W ZVS Low Voltage Induction Heating Board Module Flyback Driver Heater DIY

Feature

Description

Specification:
This section of induction heating using low-voltage DC power supply 12-48V
Maximum current 20A, maximum power 1000W
Tested 53V power supply when working properly
Because of its moderate power, can be used for small parts DIY players do hardening, annealing and other heat treatment
Also can be used with a graphite crucible melting gold, silver, copper, aluminum and other metals, uniform heating fast, very convenient
Inside diameter of the coil: approx. 40mm
Height of the coil: approx. 50mm
24V input with no load current of 3A
48V input with no load current of 6A
It suits 12-36V power supply (not included)
The coil accept 40mm crucible
Package included:
1 x ZVS low voltage induction heating board
1 x brass coil
Note:
The kit contains a full set of driving circuit elements and brass
Buyers need to bring their own power and cooling unit.
This circuit can not only be the induction heating, the copper tube also can insert into the high-frequency transformer, which is a powerful inverter.
To increase the heat sink using a customized substrate as thick as 8.5mm! Cooling capacity is very powerful.
the M4 pillars, fever smaller, more efficient.

4. 1000W 20A ZVS Low Voltage Induction Heating Board Module Tesla with Coil 12V-48V Flyback Driver Heater DIY

1000W 20A ZVS Low Voltage Induction Heating Board Module Tesla with Coil 12V-48V Flyback Driver Heater DIY

Feature

Description

Features:
24V input with no load current of 3A , 48V input with no load current of 6A
buyer need self-provided power and water cooling device
This circuit can do induction heating, or replace copper tube with high frequency transformer, it will be a powerful inverter

Note:
The kit contains a full set of driving circuit elements and brass
Buyers need to bring their own power and cooling unit.
The circuit board using double-sided fiberglass board, mainly copper traces are used to widen use the entire back surface of the resonant circuit common, continuous work, please add a fan to blow down from above, to the resonance capacitors and other components cool.
The use of switching power supply Please note that due to high power are generally slow start function, which just opened machine output voltage is slowly rising, while it is turned on before the induction heating circuit if the voltage rises to 12V, because start insufficient voltage can not afford to vibration, resulting in two simultaneous conduction mos tube so burned components.
So the first will start switching power supply voltage reaches 12V above and then access the induction heating circuit.
The volume of the object being heated inside the heating coil can not exceed 1/5 of the volume (if the heating cylinder, then heating coil diameter less than the diameter of 1/3), or it may be due to overload or burn out the power supply to the circuit.
Although this circuit can tolerate 20-30A input current moment, but do not exceed 15A when safe work, you can easily add an ammeter between the power supply and heating driver board but always monitor the current overload

Package Includes:
1 x 20A 1000W Flyback driver inductive heater Zero Voltage Switching Tesla
1 x Coil

5. ZVS Driver Module,5V-12V ZVS Low Voltage Induction Heating Power Supply Board+Heating Coil

ZVS Driver Module,5V-12V ZVS Low Voltage Induction Heating Power Supply Board+Heating Coil

Feature

Description

Specification:
Input voltage: DC 5v-12 v
Maximum power 120w (12 v induction heating). 12 v, push the ignition coil primary 5 + 5 turn, about 30 w.
PCB size: 55 mmx37 mmx1.6 mm
Heating coil, the width of the heated objects as far as possible between the heating coil diameter of 1/3 ~ 1/2, most not more than two-thirds.

Package Included:
1 x ZVS driver board
1 x heating coil

6. sainsmart 5V~12V Zero Voltage Switching ZVS Induction Heating Power Supply Module + Coil Power Supply Heating Power Supply Module

sainsmart 5V~12V Zero Voltage Switching ZVS Induction Heating Power Supply Module + Coil Power Supply Heating Power Supply Module

Feature

Description

Parameters:

1. This is no tap mini plate ZVS finished board, with no heating coil, ignition coil, and a cooling fan, etc.
2. The input voltage is DC 5-12V.
3. PCB size: 55 mm * 37 mm * 1.6 mm.

Package List:

1 x ZVS heating power supply module

Note: the product is ZVS heating power supply module, includes the heating coil

7. YosooFdit Induction Power Heating Supply Module 5V-12V ZVS Low Voltage Heating Tool with Coil Power Supply Module

YosooFdit Induction Power Heating Supply Module 5V-12V ZVS Low Voltage Heating Tool with Coil Power Supply Module

Feature

Description

Description:
Note: the product is ZVS heating Power Source module, include the heating coil.

1, this no tap mini plate ZVS finished board, with no ignition coil and a cooling fan, etc.
2, the input voltage DC 5 v to 12 v.
3, maximum power 120 w (12 v induction heating). 12 v, push the ignition coil primary 5 + 5 turn, about 30 w.
4, PCB size: 55 mm * 37 mm * 1.6 mm.
5, heating coil, the width of the heated objects as far as possible between the heating coil diameter of 1/3 ~ 1/2, most don’t more than two-thirds.
6, induction heating, power work five minutes to cool. For induction heating current is larger, heating coil is relatively large. When heated, part of the heat generated by the heated object will be passed on to the heating coil, over time, the temperature of the heating coil will be high. If the heating coil in the words of the terminal, the terminal part of plastic melt!!!! Therefore, induction heating the best heating coil directly welded to the PCB.

package include:
1 x ZVS heating Power Source module
1 x heating coil

8. 1800W ZVS Induction Heating Board Module Low Voltage High Frequency 12-48V Flyback Driver Heater with Tesla Coil and Cooling Fan

1800W ZVS Induction Heating Board Module Low Voltage High Frequency 12-48V Flyback Driver Heater with Tesla Coil and Cooling Fan

Feature

Description

Specification:
Product size:Approx.180x90x80mm (please allowed 1-3mm error)
Heater ring inner:70mm (Recommended crucible+quartz suit,maximum support of 58mm crucible)
Power supply:
New style :AC 100-220V Adapter
Old style: Main board Input voltage: 12V-48V recommend: 36V above
Power requirements: less than 12V≥10A , 15V above≥15A
NOTE:New style and Old style shipped by randomly!!!
It doesn’t affect the performance of product.!!!
Maximum power: 1800W
Maximum current: 40A
Package Content:
1 x PCB board
1 x 48V copper tube

1.The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. you can buy a small water pump and 2 meters of rubber hose(inner diameter is 4mm) for build a water cooling system
Please pay attention to using switch power supply, because output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit that will be lead to circuit can’t afford to vibrate caused by lacking voltage,so that the two MOS tube conduction and components will burned
comes with heating circle diameter-60 mm/design voltage-36V,if you use more than 40V Devices shall be used ≥70 mm diameter heating ring, DC 12V water pump use, please use separate power supply voltage regulator module to avoid fan and water pump are burn out
The minimum input is 12V, but it doesn’t mean all 12V power supply available,The module has specific requirements on voltage and current , 12V require current must than 10A ,output power will greatly reduced if the power is too low ,which will lead to two MOS conduction at the same time & burn MOS tube when lower than 12V

9. ANMBEST High Frequency ZVS Driver Module 5V-12V 120W Low Voltage Induction Heating Power Supply Board with Heating Coil

ANMBEST High Frequency ZVS Driver Module 5V-12V 120W Low Voltage Induction Heating Power Supply Board with Heating Coil

Feature

Description

Heat objects with magnetic induction! Any conductive material, usually metal, can be heated with an Induction Heater. This induction heating power supply includes a basic set of coils but can be interchanged with different coil designs and sizes.
Specifications:
Input voltage: 5V-12V 
Module Size:55 mm×37mm×16mm/ 2.17″ ×1.46″×0.63″
Coil length: approx. 75mm/2.95”
  Width: approx. 28mm/1.1” 
Maximum power: 120W (12V eddy current heating) 
Without cooling fan
Package Included:
1x High Frequency ZVS Driver Module

Conclusion

By our suggestions above, we hope that you can found Low Foltage Induction Heating for you.Please don’t forget to share your experience by comment in this post. Thank you!

Home Preview
Logo
Enable registration in settings - general